Docsis chat

Hi,

I want to test Upstream packet filtering using Upstream drop classifiers. I have never used this before and always have used IP filters instead. Could someone please let me know what are the TLVs to include in order to configure in the CM config file.

Also I read about it and it said that it needs to be configured on the CMTS also. I am using BSR 64K. Does it support the feature? If so, could you please let me know what are the commands to be used for testing Upstream Drop classifiers?

Thanks in advance,
S

hi,

I want to know the difference between load and performance testing.

i have DPC2100R2 SW_REV: v2.0.2r1242 cable modems that came online once but if you reset it, it will came in a fake online state, i have a terayon cmts BW Software Version: 4.1.6.0.5, i think maybe if i change the firmware it will work, but i tried to contact cisco, no results any ideas?

thank you

Hello all!

I'm quite new at the Docsys technology so please bare with me :) aka Docsys dummy ;)
(if you have a suggestion : docsys for dummy's. Please send me a intro or howto..)

network specs :

Nortel CMTS
os :
ARRIS MCNS Cable Modem Termination System
Software Version: 3.6.2

Provisioning :
Linux Debian distro
DHCP ( 2 pools, 1 for CM, 1 for CPE)
TFTPD
DNS
NNTP
MYSQL (DB with mac address + ip address CM network)

We're using a very default config with no BIN's!
Our basic config :
--
NetworkAcces = 1
ClassOfService =
ClassId = 1
MaxDownstreamRate = 1024000

Hi group

I wonder if someone could post a config file for DPC 2203. I have this device for testing the MTA part and the modem stays in online blinking which I think is not responding, so I think is a DOCSIS part issue.

Thanks in advanced.

Hello,

Is it possible to route a specific upstream from a same interface to a specific IPBX for the VOIP ?

Exemple :
I want that :
US0,US1 from cable interface3/0 use the IPBX 10.10.100.200
US2,US3 from cable interface3/0 use the IPBX 10.10.100.201

Thx for help

Up!

I have a Arris CMTS 1000, the question is i want to specify a secondary IP Address for CM traffic and CPE traffic or even just an Additional IP Address.

Your help is greatly appreciated

Hi everybody,

1- Date
I don't understand why i have to put an offset of 9 on the timezone in my configuration.
I am in France and normally the UTC/GMT clock is 12 when 14 in France. So the offset should be 2.

Here is the config i have :

clock timezone france 9
clock summer-time france-ete recurring last Sun Mar 2:00 last Sun Oct 3:00
clock calendar-valid

Here is the response of sh clock at 14:56 :
7246#sh clock
14:56:30.446 france-ete Mon Jun 7 2010.

2- Where can i find a free MRTG for CMTS and cable modem ?

Hi,
Have anyone configured traps on Arris 1500 and knows what must be configured besides standard access entry i nmaccess table?

After configuring access entry for traps, Arris 1000 sends traps and Arris 1500 doesn't.
[code] Access list
Index Status IP address IP mask Control Interfaces
---------- ---------- --------------- --------------- -------- -----------
1 active 192.168.X.X 255.255.255.255 read ether
2 active 192.168.X.X 255.255.255.255 read ether

Hi I've been studying up on the Cisco ubr7225 CLI. But there is one command which I can't really relate to even after reading the materials.

Whats is this "attribute" of 80000000 means? For example

cable upstream bonding-group 1
upstream 0
upstream 1
upstream 2
upstream 3
attributes 80000000

Cheers.