Docsis chat

Let me ask you a question.

There is ARRIS C3 which is license activated.

------
C3 - hostid 7236 - Licensed Features
* RIP ARSVS0XXXX
* BRIDGE_GROUPS ARSVS0XXXX
* OSPF ARSVS0XXXX

------
Is it possible to activate this license on the replacement enclosure?
Is it possible to replace with a command?

Thank you

Hello, World!
I am sure the world is asking this question. And I need your help so we can pass this knowledge on to the future forever. Here is the MOST FAQ of all time:

HOW MANY SUBSCRIBERS DOES THIS MODEM CARD (MC) SUPPORT?
(example MC: Cisco UBR-MC88V, Cisco UBR-MC20X20V-20D, Cisco UBR-MC3GX60V w/ 72DS/60US license)

Please only answer this question if you are an experience CMTS tech/Engineer only. Give us your best answer. Perhaps, we are asking the wrong question.

Hi

We have a monitoring of the upstream snr in our cisco cmts

we read the mib

1.3.6.1.2.1.10.127.1.1.4.1.5

we notice that the max value read is 36.1

so if a return has a better snr like 39 then the reading will still be 36.1

is it normal ?

is there another mib we could use that doesn't have that limit

We have run into an issue where the router behind a cable modem can't renew its dhcp lease or loses it WAN ip address. Some of our techs have figured out that they can just unplug and reconnect the ethernet cable that runs between the modem and the CPE router and the router will instantly grab an IP and be online. We used to reboot the modems and the routers but recently our guys have been trying this and it seems to work. Arris and our provisioning software company aren't much help. Has anybody run into anything like this?

Cisco-uBR10000#show cab l2-vpn xconn dot1q
MAC Address Ethernet Interface VLAN ID Cable Intf SID Customer Name/VPNID
H.H.H TenGigabitEthernet0/0/0 75 NOT MAPPED 0 LindsayCM
H.h.H TenGigabitEthernet0/0/0 76 NOT MAPPED 0 castlenetCM

Can anyone please let me know what needs to be done.

Cisco-uBR10000#show cable modem
D
MAC Address IP Address I/F MAC Prim RxPwr Timing Num I
State Sid (dBmv) Offset CPE P
7896.84e7.a8ad 0.0.0.0 C5/0/0/U3 init(d) 7 0.00 1656 0 N

It was working before and am assuming i have deleted the Bundle or something.

Am very new to this and don't know what to do.

Please help

Hi all.

I needed some help.

I made a config with 20x20V-20D + SPA24XDS without TC1000. 25DSx8US bonding. It works fine.
I want to made it with MC5x20 + SPA24XDS card too.
All DS and US bonding group is OK, everething looks fine, but the modem after a reject(na) state starts again to search the DS and after the the CM is online only in 1x1 without any bonding.

5x20 is in the 5/1 slot. SPA24XDS is in the 1/0/0 slot.

Here is the config and some output:

Hi Everyone,
As title, I test this for video stream on ip layer. But I can't watch video stream through vlc client. Below is my test topology:
windows server 2008(vlc server) - CMTS C2200 - Cable modem(bridge mode) - windows 7(vlc client)

I played a video stream on vlc server. Does any configuration need on CMTS C2200 ?
Many thanks.

Good afternoon friends.

I want to know if any of you have presented problems with the version of DHCPd version 4.1.1 of ISC Since I have a laboratory with it but it does not assign an ip address to my modem at the moment I have it configured in the following way. taking into account that I use a CISCO Ubr7240XVR.

The specifications of my server are>

Operating system CentOS Linux 6.5
Webmin version 1.680
Kernel and CPU Linux 2.6.32-431.el6.x86_64 on x86_64

Hello Everyone,

I run a docsis lab with some modem like cg3100 and tc7210.

Someone here have any possibility to provide me snmp mib file for those two modems:

Netgear CG3100
Technicolor TC7210

If you prefer send that by email, you can send it to ced1202(AT)servperso(dot)net

Thanks