Docsis chat

Hi,

i try to rehab a C2200 for a little network.
i Don't arrived to conf load-balancing

Does anybody have last firmware about C2200 ?

mine is :

CASA-C2200-CL#sh ver
Running Image: SMM Rel 5.4, Ver 19.9v6, Tue Nov 9 19:55:46 EST 2010, (rel5419)
Boot device: flash1
flash1: SMM Rel 5.4, Ver 19.9v6, Tue Nov 9 19:56:51 EST 2010, ( rel5419)
flash2: SMM Rel 5.4, Ver 19.2, Thu May 20 22:04:55 EDT 2010, ( apu)
CFE Boot: Major 2, Minor 1, Build 3

THX

Hello!
Cisco EPC3925 Cable Modem hybrid, EuroDocsis 3.0
Firmware: e3925-ES-16-c1200r5593-170428c
Hardware Version: 1.0
Administration / Manage tab
no access to the choice of Bridge Mode and Router Mode
By default it works in Bridge Mode.
Who can help firmware , Router mode is enabled or fully loaded with working firmware?

Hello group. We are looking for software called BelViewNMS for use with BelAir wireless mesh products. The manufacturer apparently no longer supports this product. If anyone knows anything about this or where we could got it, please reply. Thanks.

Hi guys,
I need help with cisco 10k, I cant lock upstream signal and I don't know why. I tried without extermal time creator...DTI, downstream ok. My config..

Hi everybody!

Can somebody help me how can I implement vendor specific OID-s to my CG3700EMR-100GES config file? I have to remotely disable some feauters on eRouter part. Specifically I have to disable the "Port Scan and DoS Protection" and "SIP ALG".

Thanks.

hello good morning I'm new to the cable internet area and I'm trying to set up a mikrotic to take over the role of administrator of the cable modems and if I replace the local sisco registry network I have already configured my dhcp server but the modem cable does not is online if someone could help me in telling me that I need to thank them.

Good Day,

I have a problem for any CM ( of diferents vendors and diferents models) when i try upgrade the firmware, the CM start download the image for upgrade but after some minutes the download fail and the conection TFTP closed, this only happen in BSR64K and with some CM no all (maybe 1500 of 14000). the TFTP server have config the timeout in "35 mins" and maxrequest in "2".

Can I assigned the static ip to CPEs?

I'm using the docsis server v3.5, and I can't find any table about IP and CPE mac address binding.

I have read previous posts, some posts mentioned the dhcpd.conf can do this, but I can't find the dhcpd.conf by using "find / -name dhcpd.conf"

What should I do??

thanks for help

So we have docsis 3 working, I have 8 contiguous channels, and another 4 non contiguous.
At one location we placed a SB6141 it came up in full channel bonding, we replaced it with a SBG6580 and no channel bonding.
Around the system sometimes we get channel bonding, sometimes we don't, and sometimes when I look at the detail the modem says Wideband Capable : N

We just turned up our first cbr8 with the 250G supervisor card.
It was a fight, getting the 100g port set correctly, but after that, it went ok.

Now, the cbr8 is online and in service, and I've found that Cacti is no longer able to see the upstream SNR on the cbr.
Doing a walk of .1.3.6.1.2.1.10.127.1.1.4.1.5 displays all 0's.
Everything else about the upstream is fine.
I've got a case opened with Cisco, but so far haven't heard any news.
Entering a show controller upstream-cable 0/0/0 | i SNR
does work.