Docsis chat

Is anyone else having issues with the Pico MiniCMTS?

As far as I have found thus far it doesn't seem to be possible to get utilization data from bonded (group) channels and/or wideband channels in DOCSIS 3.x.
Getting Channel Utilization data is only possible on mono channels, i.e. traditionally DOCSIS 2.0.
Please share your thoughts. Thanks much in advance!

Dear forum,

we want to use the Arris TG862 MTA for one of our wifi projects. Unfortunately we do not have any documentation neither do we have the vendor snmp mibs of that modem. Does anyone know if it's possible to provision the EMTA with WPA2 Enterprise to use them with PEAP? In case it's possible does someone has the corresponding snmp oids or bootfile options available?

thanks
Oliver

Any chance to get all downstream channels by remote-query?
At the moment, only the primary DS is shown.
It's a Cisco uBR10k 3G60 PRE4 with RFGW10 48QAM.

#sho cable modem wideband phy
MAC Address IP Address I/F MAC Chan Frq SNR Pwr
State Desc (MHZ) (db) (dBmV)
bc4d.fbaf.89a0 172.20.128.2 C5/0/0/UB w-online(pt) dsPri 474 43.30 0.50
dsSec 378 N/A N/A


Hi,

I need some help with settings in the config file. I want to set a locked channel and WPA2 for the wireless network one some of my modems.

I managed to get the security locked to WPA2 with 1.3.6.1.4.1.1429.79.2.2.2.1.1.4.3 / sa rg dot11bss security mode and applying the settings with 1.3.6.1.4.1.1429.79.2.2.1001.0 / sa rg dot11apply settings.

However I can't set the wireless channel. I've tried setting 1.3.6.1.4.1.1429.79.2.2.1.3.0 / sa rg dot11current channel, but the channel selection is still in auto.

Could anyone help me out here?

Thanks!

hi i just get a cmts cisco ubr7246
with 8 ds and 32 us
i would like help confi it

Helo!

I have a problem with a TX32 module card of a Motorola 64000.
After a reload of all slots the card just can't get in RUN state it just stays in boot mode and then reboot again.

show chassis status command results:

Current Time: 04/05-11:25:21
Running archive: FLASH:6421.srm4

Does anyone know how can i achieve multiple ip blocks in docsis server (https://github.com/bschirrmeister/docsis_server)

here is the example what I will gonna do.
plan1 CM ip block: 172.16.160.0 /22 CPE ip block: 10.128.0.0 /22
plan2 CM ip block: 172.16.164.0 /22 CPE ip block: 10.128.4.0 /22
plan3 CM ip block: 172.16.168.0 /22 CPE ip block: 10.128.8.0 /22

Hope someone can help me, thanks in advance.

I used STG to monitor modems in the network, somehow it works on most of the cisco modems I used. But there are modems that i cannot monitor thru STG, I learned that I need to add a specific OID to do that. Does anyone know what OID I should add on the config file? I am using Cisco DPC2320 modem.

I am looking in some of the MIBs but no luck.

Thanks in advance,

Greetings everyone, I'm running 12.2(33) SCG3 on our 7200s and SCG6 on our 10k CMTSs. I know Netflow is not supported with IPv6 on this IOS train. I glanced at the release notes up until SCJ and didn't see any Netflow support for IPv6.

Does anyone know if and when IPv6 Netflow support will be added to IOS?

Thanks,
Matt