Docsis chat

Does anyone has dpc2100 firmware, i have wrote cisco-sa but no answer

Thank you

allan_n5 (at) hotmail.com

Does anybody have the console pin out for an old Riverstone 8000?

~Carl

Hello,

we have Arris C3 cmts and i want to use the Arris Spectrum Analyzer with CPE. I tried commands snmp-server community public/private ro/rw in config mode but i cant ping cmts via cpe. Please can someone help? cca a year ago i figure it out but i forget it again. Please help i am searching all day/night internet .. you guys are my last chance. Thank you

Hi,

at this time we're Implementing our VoIP-Lab.

Our Setup:

Docsis_Server +opt122-patch -> Provisioning
BSR2000 -> CMTS
SBV5121E -> eMTA CableModems
Asterisk +ncs-patch -> VoipGW

The provisioing runs very well and the Cablemodems register with Asterisk.

We can call different eMTAs and Lines but there are no voice-flows established.

Our Asterisk-Configuration:

=mgcp.conf=

[general]
port = 2427
disallow=all
allow=alaw

[FQDN1]
wcardep => aaln/*
singlepath=no
context=from-mgcp
host=192.168.5.2
cancallforward=no
transfer=no
threewaycalling=no

Hi All,

Gang,

Still looking for some guidance on the best practice for filtering
rogue dhcp, netbios, and snmp activity from the CPE side of a
modem.
Saw this general approach in a config example posted by kwesibrunee
on another subject, and it sorta looks like a place to start? Mebbe? Perhaps?
Thanks for any assistance or direction.

Poge

Hey guys the CVC in a modem config file.. is the cvc based per model or per manufacturer ? We have to do a mass upgrade of software on various modems (5100,5101,6120 so forth) and i have done single modems via snmp but i believe i used the specific CVC motorola sent me .. and im not sure if this generic for Motorola products or for that modem model..

thanks in advanced,
Joe

Hi all,

we have an issue where Arris eMTAs need between 6 and 7 minutes to successfully register with the SIP server. Being that much too long, we set values
SnmpMib = sipCfgRegTimerMin.0 60
SnmpMib = sipCfgRegTimerMax.0 60
and everything is still the same.

After the registration, incoming calls work as they should, but outgoing calls don't.

Could it be connected to codecs? The SIP server uses ulaw and alaw codecs and we are having the following line in the MTA configuration file:
SnmpMibObject enterprises.4115.11.1.8.0 String "ULAW;ALAW;G723;G729;PCMU" ;

One of my BSR 2000 is hosed; I am getting a VxWorks prompt on boot.

Can someone tell me how to reinstall from this state? Here is what I get:

[VxWorks Boot]: @

boot device : nvram
unit number : 0
processor number : 0
file name : boot
inet on ethernet (e) : 172.16.0.19:ffff0000
gateway inet (g) : 172.16.0.254
flags (f) : 0x0
target name (tn) : bsr2000

Start application from NVRAM:
Booting image boot
isValidAppImage: Ram file checksum disagrees with original checksum!
Original xsum = 0x30302067, New xsum = 0xacd6f24c

Hi all,

could someone please encode the following parameters in the configuration file with the Arris PacketAce and attach the binary file:
SnmpMib = sipCfgRegTimerMax.0 1800
SnmpMib = sipCfgInviteLinger.0 16000
SnmpMib = sipCfgRepeatDialingTimeout.0 1800
SnmpMib = sipCfgSessionExpires.0 1800

We just need the OIDs of the encoded parameters ...

Thank you very much for quick reply!