I have the follow Cisco CMTS equipment available for sale. All are in stock located in Orange County, California. It's been fully tested by certified Cisco technicians and backed with a 1 year warranty. There's also FREE shipping included anywhere inside the continental United States. Please contact me if you have any interest, questions or concerns.
Hi
i want to disable the communication between the cpe's connected to the CMTS . to do this i have applied the below access rule to config file. but it dasn't seems to work. pls advice me.
access-list 102 permit ip any host 10.1.0.1
access-list 102 permit ip any host 10.1.0.2
access-list 102 deny ip any 10.1.0.0 0.0.7.255
access-list 102 permit ip any any
interface BVI1
ip address 10.1.0.1 255.255.248.0
ip access-group 102 in
## running config file ##
Router#show running-config
Building configuration...
I'm trying to connect new cablemodem ARRIS TM902S with telephony.
Internet works fine, but telephony stops at:
Telephony-DHCP Completed
Telephony-TFTP In Progress
Telephony-Reg with Call Server In Progress
Telephony-Reg Complete Line(s): Not Registered
in EVENT LOG shows:
eventid: 4000950203
description: Provisioning Server FQDN unknown to the DNS Server
I'm using the same config file, what i'm using it on ARRIS TM602B, TM601B, but they works great!
I´m attempting to running Cable Modem service using a Mikrotik to support CMTS servers requeriment. In fact, the CMTS router demands DHCP, TFTP and NTP servers and it can work like transparent bridge.
Somebody knows about it?. is this possible? The Mikrotik can support CMTS request?
Thanks in advance for your help.
I'm trying to find Standard OID's to obtain Service Flows for several devices (Arris, Motorola, S-A). After reading rfc4323, and checking mibDepot.com I thought I had the answer with the OID table 1.3.6.1.2.1.127, but it didnt work on Arris or S-A, so my guess is that this isnt an Standard OID or maybe is a CMTS OID, am I right? is there a Standard OID that i can use to get ALL Service Flow Table from a CM (primary and secondary)?
Hello all,
I have a small sized cable network equipped with few C2200 CMTS from Casa Systems (http://www.casa-systems.com/products/c2200-series) and found that we cant configure static ARP entries. I see commands for changing/viewing ARP requests intervals but nothing about setting any IP entry to static or manually configured.
Thanks.
Hello all,
There has been a lot of talk about cable modem configs, but it seems like the conversation is never finished, or adequately answered. It would be great if everyone would post their best modem config (bin file renamed png) or the text version, and what program you are using to build them. It would be nice to see some configs with filtering enabled to block dhcp, and what about blocking cpe's for non-subscribers while authing the modem?
Thanks, this will be a great help to those of us running minimal configs and no test environment...
I have a DOCSIS3 CMTS with standard US 6 MHz channels. Is there any reason why I couldn't set up my down streams to
10 MHz Euro DOCSIS channels to gain more bandwidth ? We are testing IPTV and I would think the extra 4 MHz/channel
would be helpful as we get more usage.
I have a fundamental question on routing in a CMTS. (E.g BSR64000/CISCO CMTS)
Where do the ROUTING protocols run? Is it on the network side or CPE side?
If it is on network side, what is the need for routing since default gateway would be ISP router?
If it is on CPE side I am again not clear why routing would be reqd. ?
Is it possible for routers to be connected behind a CM?
