Docsis chat

Anybody out there ever set up Docsis30 Loadbalancing based on Cisco modem-count loadbalancing?
The command "cable load-balance docsis30-enable" was introduced in IOS SCF.
Now i would like to use the 'dynamic bonding change' for D30 modem. So far I've set up the following:

cable load-balance docsis30-enable
!
cable load-balance docsis-group FN 3 MD Cable6/0/1
no disable
method utilization us-method utilization
interval 30
threshold load 10
threshold load minimum 3
threshold stability 50


Hi there,

I just want to revive some Motorola sbv5121e voip cable modems.
I have read many articles on this site, but the mta part will not work,
and i ran out of ideas. I could use a little help.

Here is the test dhcpd.conf file:

authoritative;
allow leasequery;
ddns-update-style none;
ignore client-updates;
next-server 192.168.33.1;
option domain-name-servers 192.168.33.3;
option domain-name "mta.domains.net";
option tftp-server-name "192.168.33.1";

I would like to don't have any wideband capable modem in only one freq. and I tried to solve with thew command 'Cable Wideband Autoreset' but so far without sucess.

how I define the qos profile to a cable modem?

Hello,

I need to figure out the MTA OnHook/OffHook Status of the two lines via SNMP

I got the following information from a friend, but did not work for me. I got no output

.1.3.6.1.4.1.2863.78.3.2.1.6 tmmMtaEndPntHookStatus onHook->0 offHook->1

Does someone know the OID which I need to ust to get the status via SNMP?

Thanks

Harald

I'm having some problems getting remote-query working on a ubr7246. I've got the cmts set to use remote-query, and I'm sure I'm using the right community as I can poll the modems via other snmp utilities. The subnet allowed to access snmp defined in the modem includes the remote-query src ip that I'm using.

Debugging snmp on the CMTS yields:

5d22h: v1 packet
5d22h: community string: cm_client_skinner
5d22h:
For IP address 172.31.32.23
5d22h:
SNMP proxy exec got event,but queue is empty

'show snmp sessions' says:

Hi guys,
hope you're OK today. I have a question about DOCSIS 3.0 config file.
As we know, Cable modem DOCSIS 3.0 used config file D1.1. The different Cable modem D3.0 has a capability to use channel bonding. How to make it different between DOCSIS 1.1 and 3.0.

So, I'm trying to get a l2vpn working in my test setup, looks like this:

TP-Link Router (192.168.1.1)- (straight-cable)switchport hooked to cable modem (bpi enabled)
7225 cmts, with the following lines
cable l2-vpn-service xconnect nsi dot1q interface GigabitEthernet0/2
cable dot1q-vc-map 001d.d3f2.7b09 GigabitEthernet0/2 30
cable dot1q-vc-map 001d.d3f2.7aa5 GigabitEthernet0/2 31

(gig0/2 is configured with 10.1.1.2 ip address)
connected to gig0/2 is a cisco 2621, port fa0/0 (crossover cable)
following lines:

Hello all,
can we help me and send me

Config file modem for arris tm822s modem and MTA for access Docsis 3.0 ? :(

my email:
gmotyw@o2.pl

thank.

I have two CMTS routers (BSR 64k), one supports 4 channel bonding and the second supports expanded bonding (up to 8 channels).

When I connect an SB6121 to the first, it registers on all four channels and the router shows it is properly bonded. Modem traffic graphs show traffic across all four channels.

When I connect the same modem to the second router which is configured for 5 channels, the modem shows it is registered on 4 channels but the router does not show it is properly bonded. Furthermore, traffic graphs show traffic on a single channel.