Docsis chat

Hi !

I'm new to the DOCSIS world. Can someone tell me the difference between cablemodem config files ?
I have found .bin and .cfg files. They don't look the same.

Is one of them preferable over the other ? When should you use .bin and when .cfg ?

Does anyone have any experience trying to set static multicast sessions on cable modems?

Specifically, using TLV 64 (CMTS Static Multicast Session Encoding).

I have the group entered, and a CMIM of 47FF (should cover all CPE interfaces).

I believe the problem I am running into is with the extended MIC settings. I am trying to flag TLV 64, but just not quite sure how to do it. Is it supposed to be a binary value or a hex value (that represents said binary value?). Or something else?

Any help would be greatly appreciated!

Thanks!
--John

Hello!
Has anyone worked before with those features (DBWS and ACFE)??

I am new at this forum and I am trying to set up a Docsis 3.0/1.1 environment taking advantage of those features. Specifically what I am trying to do is to configure in a single service group all the DS channels as primary and as bonded channels as well, and share the bandwidth among them as fairly and load balanced as possible. This will allow me to get the legacy modems online as well as the 3.0 modems. Does this makes sense to you guys?

I would like to know if I can still use docsis_server or the project is dead ?
https://github.com/bschirrmeister/docsis_server

Is it safe to use and/or can a server running it be updated without breaking docsis_server ?

Is there anyone that eventually can help with installation ?

Thx

:-) Jens

Anyone, I need help , I'm trying to setup c3 arris but modem always get stuck init(o) , I found log : No Ranging Requests received from POLLED CM (CMTS generated polls). , and there is no log that modem has request tftp docsis file. cable modem has get ip modem and I can ping.
I have searching any solution from any forum but no luck. any solutions ?

Motorola SB5101i
Ranging/Registration : init(o) - modem ready to download config file

this is my dhcpd.conf (it works for cisco ubr7200)

Anyone know what the TlvCode for MDD override (MIMO) is? I'm looking at IpProvMode but I'm not sure that's correct, anyone know otherwise? I'd like to get IPv6 up and running :)

Hi,
We are professional CMTS manufacturer here in China; we sell the most cost effective CMTS (DOCSIS1.1.DOCSIS2.0, DOCSIS3.0) all over the world. Up to now, our CMTS has been deployed over more than 30 countries and places successfully.
We are now majoring in DOCSIS 3.0 CMTS solution. Enclosed we are sending you our latest version of all products, please check whether they could meet your requirements.

Hello everyone, I know that this is not a "docsis" question but I hope so that you can help me about this dilemma. I'm new in one cable tv company in BiH , and we have many problems with some optical nodes that are joined together, and to time to time we have noise or modems just goes off. Problem is that for example 3 nodes have the same return path wavelength(1310nm)with fp laser and there are joined with optical spliter 1/3 (33%) ,and send back to optical receiver with one fiber.

Hi i have strange issue .

I have a strange issue

CMTS 7246 is generating some invalid code 0 , and behind CMTS i have a huawei ruter that show message in log :

Line 24887: Sep 11 2014 01:24:47+02:00 DST PG-NPE1 %%01SNOOPING/4/HTYPEERR(l)[342123]:Slot=5,Vcpu=0;The type of hardware address in DHCP packet received from interface GigabitEthernet5/0/1.1001 VLAN 1001 was wrong!

I found in RFC :

RFC 2131 Dynamic Host Configuration Protocol March 1997

Hi All,
I want develop small software view signal on cable device or bandwidth on interface cable, i not found info with snmp oid string. Pls, Help me.
Thank!