Docsis chat

Dear All,
We are working as a Cable Modem ISP in Saudi Arabia. We have purchased a refurbished Cuda 12000. When we connect power and Controller card then Its display an error in Japanese Language and Status on Controller card is "D2". Can anybody help me what to do next???

Hello,
I am working on docsis 2.0 with an Arris C4 CMTS and a RCA modem.
I wish doing SA dynamic multicast with my modem online in bpi+ mode.
I have been succeeded in doing static multicast in Bpi mode in making the configuration of CMTS by CLI and as well by MIBs.

Hello there,
I am trying desperately to get the Motorola SB3100, SB4100 to accept DOCSIS 1.1 configuration files. According to what I have read on Motorola's documentation, these modems should support DOCSIS 1.1. However, when using a DOCSIS 1.1 service flow config scheme config, the modem gets stuck on the online light (flashing) and the CMTS reports "init(o)" status. Sh cable modem verbose reports:
MAC Version : DOC1.0
QoS Provisioned Mode : DOC1.0

Hi guys,
I usually use the forum as a way of keeping up what others are up to but I need a bit of help and a steer.I have a small,ad-hoc, test bed (I work for a large MSO) which is a Cisco VXR7246, with MC28U,MC16C and and a NPE-G1. We have a varying degree of modems on it,small numbers. I use the CMTS mainly for trying out and troubleshooting the RF/HFC features of the IOS plus new CPE that go to the field, rather than the routing/load balancing/subscriber management etc etc side of things.So its a basic set up.

Hello,

Im configuring a cuple of Arris C3 CMTS'es, and for some reason cablemodems keep on ranging, they "see" power on the frecuency configured, but they dont stop ranging, I even tried to use one ofe the sample configuration scripts on the User Manual. They dont even get to lock on the Downstream.

Any comment will be apreciated.

Thanks,

Hello everyone,

I configured the IP and contact information, using this commands under box subsystem

$ box
contact "admin@tomtel.ru"
name "ARRIS-9"
location "TOMSK,TOMTEL"
$ ip-level
config-ip-address 213.210.81.13
config-ip-subnet 255.255.255.192
config-ip-gateway 213.210.81.1

After configuring it I just rebooted the cmts, and it preserves the contact info but no the ip config.

Anyone nows how to save this configuration??

Thanks in advance...

I have several ADC CUDA 12000 server chassis and circuit boards that we are looking to get rid of.

Below is a list of the

units I have and what we would like to get for them. Im fairly flexible on the prices, especially for a

larger order.

Please let me know if you are interested.

Thank you,
Zackary O'Brien
zack@dmdsystems.com
602-307-0180

ADC CUDA 12000 SERIES CHASSIS(1X6) C12+N+1BASE W/CARDS
2x 1GB ETHERNET, 2x C12-MM2 MANAGEMENT, 2x 1x6 DOCSIS 2
US $4,500.00

Hi, everyone

I am a new in cm and docsis, I am trying to bring up the moto SBV5121E. It's sucessful connecting to the provisioning server, and completing the dhcp both for cm and mta, and their tftp download are sucessful too, but the mta provisioning failed. what's the necessary TLV for BASIC.2 flow in the mta config file?

I recently bought a Cisco uBR-7246 with a single MC88V and a couple of Motorola 6120 DOCSIS 3.0 capable modems and I am trying to get my system up and running with the "All in one" setup. I struggled with this because the "All in one" setup doesn't use my MC88V line card, so I had to dig around to figure out how to setup the IP address in a Bundle.

Here is the setup:
MC88V_U0-U3-->4to1_combiner-->40dB-pad-->diplex_flt(low-side)
MC88V_D0-->40dB-pad-->diplex_flt(high-side)
diplex_flt(common)-->Moto_6120(cable-modem)

Hello, I'm new in this forum.

Last week I noticed a small problem in my network. Cable modems and host have a strange problem in renewing IP addressess.

When modem boots up it gets IP and config from tftp server and looks fine and works.
After half of dhcp-lease time ( like in dhcp std. ) modem and CPE tries to renew its address.
In this case I can see in logs many entries like this:

Mar 13 06:25:14 172.16.1.210 CABLEMODEM[DOCSIS]: <68010100>DHCP RENEW sent - No response

and log from dhcp server looks like :