Docsis chat

Hello,

I have CMTS uBR10000 (PRE2-RP), version 12.2(33)SCE5 and had to reload it. AFter restarting it , the card ubr10k-clc-mc2020v is stucking in loading and cannot finish loading. I received the logs below
*Jul 9 01:44:50: %UBR10KTCC-1-NOTCC: No working TCC card available in the system
*Jul 9 01:45:00: %IPCOIR-5-CARD_DETECTED: Card type ubr10k-clc-mc2020v (0x641) in slot 8/1
*Jul 9 01:45:00: %IPCOIR-5-CARD_LOADING: Loading card in slot 8/1 sw version 1.0 code MD5 D41D8CD98F00B204E9800998ECF8427E fpga MD5 0000000000000000000000000
0000000

Hi,

I would like to know if any of you have material on creating a hotspot in docsis 2..

thanks,

Good afternoon
Could you help me please,

Using OID, I need to block GUI and Telnet access to Cable modems. Only allow this access to a specific network segment.

for example:
Allow GUI to 10.10.10.0 255.255.255.0
Allow Telnet to 10.10.10.0 255.255.255.0
Block GUI to all
Block Telnet to All.

The cable modem is Thomson DWG855 and Technicolor TC7300, especially CM with Chipset "BROADCOM"

thank you in advance for your help

Regards,

Hello everyone.
I am trying to provision default wifi settings on cable modem Thomson TWG870.
We are using arris c4 cmts.
The problem is that when i add mibs to config file modem stucks at DhcpV4Done. No cpe address, no mta address
Where could be the problem?
Config is attached

I'm managing a UBR7246VXR chassis and I have a question. I want to install two UBR-MC88V, one of them configured with D3.0 (Annex B) and the other one with D3.0(Annex A). Is there any problem to do this or in the same chassis is mandatory to use the same annex in all the cards.

Hello,

Hi to all

I am having trouble configuring IPDR on a BSR 64000.
When i use this configuration :

ipdr enable
ipdr acksequenceinterval 64 ( default )
ipdr acktimeinterval 30 ( default )
ipdr keepaliveinterval 60 ( default )
ipdr collection-interval 15
ipdr export current-streaming-time
ipdr source-interface "my interface that reaches the collector"
ipdr collector "a.b.c.d" 4737 0 ( default ) - it takes as servicedefinition d2-samis

The file is generated in the collector, but not in the .xml format.

Hello,

I've recently obtained several BSR64k units with SRM4, TX32 and RX48 modules. Everything was running various software and bootrom versions. My research on the topic shows that I should be running 6.4.x.x software on all modules and bootrom 7.x.x.x.
As far as I can tell the latest v6 software should be 6.4.2.3 - is that correct? Can someone please share a link to a downloadable version of this fw?
Can someone also share the latest recommended bootrom in the v7 series?

I've also stumbled upon a POST error on several TX32 modules:

Hello!
I search for docsis config generator what allow more than 52000000 max rate down.
Of course for linux.

million thnaks

Hello to all!!

I am using 4 arris c3 cmts in one HFC plant. All cmts are managed by DMA SoftLab (radiusmanager with docsis support) .
All 4 CMTS are configured and working good i have no problems with configuration.
Lets assume:
CMTS1 410 MHz
CMTS2 418 MHz
CMTS3 426 MHz...etc

What is my problem?!!