I have uBR10K CMTS as M-CMTS and on that i have configured 615 MHz channel as primary and two channels on RFGW-1 621 & 627 MHz. When i connect SMC3DGN modem on it, modem gets online through following :
init(r1)
init(rc)
init(i)
init(o)
w-online (Docsis 3.0 mode)
and after 2-3 seconds it goes "offline". again it starts ranging and gets in the same loop.
But when i shut my "interface wideband" - the same modem goes through same steps and finally remains in "online" state (Docsis 2.0 mode).
Can anyone have an idea why my modem keeps flapping when in Docsis 3.0 ? how can i stop that ?
Mar 29 20:18:07.207: SPA 0 Done. 0 used, 65502 free. Fwd to Jacket @ 1/0
Mar 29 20:18:33.823: UDP: rcvd src=0.0.0.0(68), dst=255.255.255.255(67), length=
529
Mar 29 20:18:33.823: UDP: sent src=10.125.1.1(67), dst=10.20.1.253(67), length=5
29
Mar 29 20:18:33.839: UDP: rcvd src=10.20.1.253(67), dst=10.125.1.1(67), length=4
38
Mar 29 20:18:33.839: UDP: sent src=10.125.1.1(67), dst=10.125.9.93(68), length=4
38
Mar 29 20:18:33.983: UDP: rcvd src=0.0.0.0(68), dst=255.255.255.255(67), length=
541
Mar 29 20:18:33.983: UDP: sent src=10.125.1.1(67), dst=10.20.1.253(67), length=5
41
Mar 29 20:18:33.983: UDP: rcvd src=10.20.1.253(67), dst=10.125.1.1(67), length=4
38
Mar 29 20:18:33.983: UDP: sent src=10.125.1.1(67), dst=10.125.9.93(68), length=4
38
Mar 29 20:18:36.115: UDP: rcvd src=10.125.9.93(1039), dst=10.125.1.1(37), length
=9
Mar 29 20:18:36.563: wb_stat_set_gur_idx_reg() 5/1/0, 0026.f39a.248d,
Mar 29 20:18:36.563: cmts_get_cm_guardian_info wcm=1 if_num=0, Bay 0, Guardian 5
/1 sid:113 228 tot:1
Mar 29 20:18:36.563: wb_stat_set_gur_idx_core() sfid:idx
Mar 29 20:18:36.563: Stat Idx assign: uniq_idx:128 spa_num=0 spa_if=0 if_sid:0x7
1 Unused:65502
Mar 29 20:18:36.563: wbcmts_idxtbl_assign(): uniq_idx:128 if_sid=0x71 sfid:idx=2
28:373 tbl=0x61742358 Idx = 373 tot:1
Mar 29 20:18:37.123: wbcmts_sch_rp_stat_upd_srv_flow() 228:373
Mar 29 20:18:37.123: Entry exists 228:373 228:373
Mar 29 20:18:36.563: IPC(len=30)-> Jacket(1/0/0)
Mar 29 20:18:36.563: wb_stat_set_lc_idx_core() sfid_num:1 sid:113 228:373 CM sta
te:13. Sending IPC -> LC(5/1) state:13 -- EARLY
Mar 29 20:18:38.031: UDP: rcvd src=0.0.0.0(68), dst=255.255.255.255(67), length=
399
Mar 29 20:18:38.035: UDP: sent src=10.250.1.1(67), dst=10.20.1.253(67), length=3
99
Mar 29 20:18:38.035: UDP: rcvd src=10.20.1.253(67), dst=10.250.1.1(67), length=4
56
Mar 29 20:18:38.035: UDP: sent src=10.125.1.1(67), dst=10.250.8.114(68), length=
456
Mar 29 20:18:37.159: Adding TLV: blaze index 373 for SFID 228
Mar 29 20:18:37.159: Add TLV Done: Added 1 blaze indices
Mar 29 20:18:37.159: wbcmts_check_blaze_indexes() NO zero index detected, CM:002
6.f39a.248d
Mar 29 20:18:41.123: UDP: rcvd src=0.0.0.0(68), dst=255.255.255.255(67), length=
399
Mar 29 20:18:41.123: UDP: sent src=10.250.1.1(67), dst=10.20.1.253(67), length=3
99
Mar 29 20:18:41.123: UDP: rcvd src=10.20.1.253(67), dst=10.250.1.1(67), length=4
56
Mar 29 20:18:41.123: UDP: sent src=10.125.1.1(67), dst=10.250.8.114(68), length=
456
Mar 29 20:18:43.835: wbcmts_release_service_flow_reg[5/1]: Free 373, SFID 228
Mar 29 20:18:43.835: cmts_get_cm_guardian_info wcm=1 if_num=0, Bay 0, Guardian 5
/1
Mar 29 20:18:43.835: wbcmts_release_service_flow_reg: alloc buffer, bay 0
Mar 29 20:18:47.207: wbcmts_send_blaze_free_indices_msg_to_guard mod:2 tot:1 si
z:18
Mar 29 20:18:47.207: wb_stat_del_gur_idx_core: SPA 0, Releasing 1 indices
Mar 29 20:18:47.207: wb_stat_idxtbl_freeup() spa:0 idx:373 228:373 if_sid:0x71 s
id:113 nb_idx:128 freed 373
Mar 29 20:18:47.207: SPA 0 Done. 0 used, 65502 free. Fwd to Jacket @ 1/0
post your show run (sanitized)
also debug with these options
debug cable mac-address xxxx.xxxx.xxxx verbose
Debug cable mdd
Debug cable registration
Debug cable range initial
debug cable md-sg
debug cable range
debug cable range protocol
Debug cable ubg
debug cable service-ds-selection event
debug cable service-ds-selection timer
and log the output.
Thank you Capm. Running config & logs are attached for your reference.
************
version 12.3
no service pad
service timestamps debug datetime msec
service timestamps log datetime msec
**
boot-start-marker
boot system disk0:ubr10k2-k8p6u2-mz.123-23.BC10.bin
boot system flash bootflash:
boot-end-marker
***
card 1/0 2jacket-1
card 1/0/0 24rfchannel-spa-1
card 1/1 2cable-tccplus
card 3/0 1gigethernet-hh-1
card 5/0 5cable-mc520s-d
card 5/1 5cable-mc520s-d
cable admission-control preempt priority-voice
cable modem remote-query 10 cabletech
cable modulation-profile 26 request 0 16 0 22 16qam scrambler 152 no-diff 72 fixed
cable modulation-profile 26 initial 5 34 0 48 16qam scrambler 152 no-diff 196 fixed
cable modulation-profile 26 station 5 34 0 48 16qam scrambler 152 no-diff 196 fixed
cable modulation-profile 26 short 4 76 7 22 16qam scrambler 152 no-diff 128 shortened
cable modulation-profile 26 long 9 232 0 22 16qam scrambler 152 no-diff 128 shortened
cable service attribute ds-bonded downstream-type bonding-enabled
no cable qos permission create
no cable qos permission update
cable qos permission modems
cable time-server
cable clock dti
***
ip subnet-zero
!
!
redundancy
!
!
controller Modular-Cable 1/0/0
ip-address 172.20.1.253
modular-host subslot 5/1
rf-channel 0 description CMTS3.0 Bonding channel 1 port 1.1
rf-channel 0 cable downstream channel-id 1
rf-channel 0 frequency 621000000 annex B modulation 256qam interleave 32
rf-channel 0 ip-address 172.20.1.251 mac-address 0023.be60.7fa0 udp-port 49152
rf-channel 1 description CMTS3.0 Bonding channel 2 port 1.2
rf-channel 1 cable downstream channel-id 2
rf-channel 1 frequency 627000000 annex B modulation 256qam interleave 32
rf-channel 1 ip-address 172.20.1.251 mac-address 0023.be60.7fa0 udp-port 49408
rf-channel 2 description CMTS3.0 Bonding channel 2 port 1.3
rf-channel 2 cable downstream channel-id 3
rf-channel 2 frequency 633000000 annex B modulation 256qam interleave 32
rf-channel 2 ip-address 172.20.1.251 mac-address 0023.be60.7fa0 udp-port 49664
******
!
!
!
interface FastEthernet0/0/0
ip address A.B.C.D 255.255.255.0
duplex full
speed 100
!
interface Wideband-Cable1/0/0:0
description D3.0 LAB Channel Bonding C5/1
no ip address
cable bundle 1
cable bonding-group-id 1
cable rf-channel 0
cable rf-channel 1
!
interface GigabitEthernet3/0/0
ip address 10.20.1.1 255.255.255.0
negotiation auto
!
interface GigabitEthernet3/0/0.1
encapsulation dot1Q 3
ip address 10.2.1.126 255.255.255.0
!
***
interface Cable5/1/0
no ip address
no cable packet-cache
cable bundle 1
cable downstream channel-id 25
cable downstream annex B
cable downstream modulation 256qam
cable downstream interleave-depth 32
cable downstream frequency 615000000
no cable downstream rf-shutdown
cable upstream max-ports 4
cable upstream 0 connector 0
cable upstream 0 frequency 26000000
cable upstream 0 docsis-mode tdma
cable upstream 0 channel-width 1600000 1600000
cable upstream 0 minislot-size 4
cable upstream 0 range-backoff 3 6
cable upstream 0 modulation-profile 21
no cable upstream 0 shutdown
** cable upstream 1 shutdown
** cable upstream 2 shutdown
** cable upstream 3 shutdown
!
interface Cable5/1/2
no ip address
no cable packet-cache
cable bundle 1
cable downstream channel-id 33
cable downstream annex B
cable downstream modulation 256qam
cable downstream interleave-depth 32
cable downstream frequency 639000000
no cable downstream rf-shutdown
cable upstream max-ports 4
cable upstream 0 connector 8
cable upstream 0 frequency 26000000
cable upstream 0 docsis-mode tdma
cable upstream 0 channel-width 1600000 1600000
cable upstream 0 minislot-size 4
cable upstream 0 range-backoff 3 6
cable upstream 0 modulation-profile 21
no cable upstream 0 shutdown
** cable upstream 1 shutdown
** cable upstream 2 shutdown
** cable upstream 3 shutdown
****
!
interface Bundle1
ip address 10.250.1.1 255.255.0.0 secondary
ip address 10.125.1.1 255.255.0.0
no ip route-cache cef
no ip route-cache
cable arp filter request-send 3 2
cable arp filter reply-accept 3 2
no cable arp
cable dhcp-giaddr policy
cable helper-address **MY_CNR_IP**
!
router eigrp 26
network 10.0.0.0
auto-summary
!
ip classless
ip route 0.0.0.0 0.0.0.0 Bundle1
ip route 10.50.0.0 255.255.0.0 10.2.1.240
no ip http server
no ip http secure-server
!
!
!
dialer-list 1 protocol ip permit
cdp run
nls resp-timeout 1
cpd cr-id 1
snmp-server community ********* RO
snmp-server community ********* RW
snmp-server manager
tftp-server disk0:myconfigfile.bin alias myconfigfile.bin
!
!
***!
!
cable fiber-node 1
downstream Cable5/1/0
downstream Modular-Cable 1/0/0 rf-channel 0-1
upstream Cable 5/1 connector 0
!
cable fiber-node 2
downstream Cable5/1/2
upstream Cable 5/1 connector 8
!
end
Well, right off, I don't see a wideband interface configured, it may be slightly different for yours, but something like this:
interface Wideband-Cable1/0:0
cable bundle 1
cable bonding-group-id 1
cable rf-channel 0 bandwidth-percent 90
cable rf-channel 1 bandwidth-percent 90
cable rf-channel 2 bandwidth-percent 90
cable rf-channel 3 bandwidth-percent 90
!
interface Integrated-Cable1/0:0
cable bundle 1
cable rf-bandwidth-percent 10
!
interface Integrated-Cable1/0:1
cable bundle 1
cable rf-bandwidth-percent 10
!
interface Integrated-Cable1/0:2
cable bundle 1
cable rf-bandwidth-percent 10
!
interface Integrated-Cable1/0:3
cable bundle 1
cable rf-bandwidth-percent 10
Also, try removing this line, I don't think its needed unless you need to force something:
cable service attribute ds-bonded downstream-type bonding-enabled
Any particular reason you're using a custom modulation profile?
Try removing those lines and replace them with:
cable modulation-profile global-scheme
hey,
thanks for help.. but i believe i have interface wideband configured and controller modular configured.
i use M-CMTS - (DTI server, Cisco RFGW1, uBR 10k) solution. can u guess what could b wrong ?
Did you try this -
---------
Also, try removing this line, I don't think its needed unless you need to force something:
cable service attribute ds-bonded downstream-type bonding-enabled
Any particular reason you're using a custom modulation profile?
Try removing those lines and replace them with:
cable modulation-profile global-scheme
--------
You don't have a frequency set in your cable modem profile do you? Also, is the modems firmware up to date? Have you tried another brand/model of modem? Have you tried an 8x4 modem? (I realize you're not bonding 8 channels, but the modems have different hardware/software)
You can't be far off, the modem is getting into the bonding group and coming online, so its got to be something relatively simple.
it was my typo mistake in typing MAC address of EQAM. just corrected it and modems are locked on w-online status.. Thanks for support.
Now i want to know:
- i see some CM with "online" (D2) status and some with "w-online" (D3). I can makeout that w-online is Docsis3 and online is Docsis2 CM. But how do i know these Docsis 3 modems are locked to which bonded channels ?
- When i login to D3 CM and check RF status, it shows locked to primary, bonded1 and bonded 2 downstream and locked to upstream. I need to check same from uBR10K.. suggestions please.
Try....
show cable modem xxxx.xxxx.xxxx wideband rcs-status
This wont work as i run 12.3.23 BC10 IOS.
I have following:
uBR10k#sh cab modem x.x.x.x wideband ?
primary-channel Display Primary Downstream
| Output modifiers
uBR10k#sh cab modem x.x.x.x wideband primary-channel
MAC Address IP Address Host MAC Prim Num Primary DS
Interface State Sid CPE Downstream RfId
xxee.yyee.xxee x.x.x.x C5/1/0/U0 w-online 171 4 C5/1/0 255
Any other way out ?
I'm not sure there is a specific command for that information now, it seems to show just the rcc index now, and then you would then derive the information from that template. here is the manual entry for the command:
http://www.cisco.com/en/US/docs/ios/cable/command/reference/cbl_16_show_...
The way I understand it, bonding is either all-or-nothing, either you bond all channels in the template, or it assigns a different template, or you don't bond at all.
i m nothappy with cisco page.. nothing on this page applies to my IOS version.
But i found something else ..
uBR10k#sh controllers cable 5/1/0 downstream
Cable5/1/0 Downstream is up
Frequency 615.0000 MHz, Channel Width 6 MHz, 256-QAM, Symbol Rate 5.360537 Msp
s
FEC ITU-T J.83 Annex B, R/S Interleave I=32, J=4
Downstream channel ID: 25
Dynamic Services Stats:
DSA: 0 REQs 0 RSPs 0 ACKs
0 Successful DSAs 0 DSA Failures
DSC: 0 REQs 0 RSPs 0 ACKs
0 Successful DSCs 0 DSC Failures
DSD: 0 REQs 0 RSPs
0 Successful DSDs 0 DSD Failures
DCC: 0 REQs 0 RSPs 0 ACKs
0 Successful DCCs 0 DCC Failures
DCC end of transaction counts:
DCC unknown cause(0) offline(0) if down(0) no cm(0)
DCC no resource(0) no retries(0) reject(0) unknown state (0)
DCC rebuild err (0) T15 timeout(0) wrong channel(0) reinit MAC (0)
DCC dcc succeeds(0)
DCC wcm(0)
Local total modems 2, modems active 2, total DS flows 3
NB DS Mo1/0/0:0, STATE: DOWN
Frequency 621.0000 MHz 256-QAM, ANNEX B, R/S Interleave I=32, J=4
Network Delay 550 (usec)
Bandwidth (Kbps): 16875, Load Percent: 0
Channel ID: 1, US MAP: 0x000F
Total modems: 0, modems active : 0, total DS flows: 1
NB DS Mo1/0/0:1, STATE: DOWN
Frequency 627.0000 MHz 256-QAM, ANNEX B, R/S Interleave I=32, J=4
Network Delay 550 (usec)
Bandwidth (Kbps): 16875, Load Percent: 0
Channel ID: 2, US MAP: 0x000F
Total modems: 0, modems active : 0, total DS flows: 1
NB DS Mo1/0/0:2, STATE: DOWN
Frequency 633.0000 MHz 256-QAM, ANNEX B, R/S Interleave I=32, J=4
Network Delay 550 (usec)
Bandwidth (Kbps): 16875, Load Percent: 0
Channel ID: 3, US MAP: 0x000F
Total modems: 0, modems active : 0, total DS flows: 1
DS_chan_id RFID Interface
--------------------------------------
1 0 Mo1/0/0:0
2 1 Mo1/0/0:1
3 2 Mo1/0/0:2
--------------------------------------
MDDs Primary Non-Primary
----------------------------------------------
Local 168046 0
1/0/0:0 0 168043
1/0/0:1 0 168043
1/0/0:2 0 125017
----------------------------------------------
*************
Interestingly modem shows blue LED, its status page shows locked to multiple downstreams.. but above command says ...
>> NB DS Mo1/0/0:0, STATE: DOWN, NB DS Mo1/0/0:1, STATE: DOWN .... what is that ?? i am still interested in knowing what downstreams (bonded) am i connected to ?
NB = Non-Bonding
The Cisco manuals can be confusing because, for example, the update sheets for the 7200 software are all derived from the 10k sheets, their software is nearly identical, but yet, such subtle differences.
So its not bonded ? why the status is then w-online and CM shows all downstreams locked ?
Do you have any non-bonding modems hooked up?
Yes. I have docsis 2 modems along with Docsis 3 too. D3 modems were locked to only primary downstream (online - green LED indication on DS)when i remove wideband config. After wideband is configured D2 modems are still locked as D2 (online) and D3 modems turned to D3 (blue LED indication on DS- CM status page shows 3 downstream locked).