UBR10012 - 2 x DTCC card problem | docsis.org

You are here

UBR10012 - 2 x DTCC card problem

8 posts / 0 new
Last post
wrangler
UBR10012 - 2 x DTCC card problem

Hi there,

We got a new ubr10012 where we want to run 2 DTCC Card with IOS Version 12.3(17b)BC9.

We unpack and power up the machine. But the ubr seem to not recognize DTCC Card. Also, we tried to fix the card 1/1 and 2/1 in the config, but no result. We have also 1 card mc20x20v. We want to use the solution I-CMTS, without clock server. I read we need to put on the dtcc card first, otherwise, we cant use mc20x20 card.

Anyone have idea ? Below, config file (basic because we dont have access to advance config)

May 20 09:12:13: %IPCOIR-3-CARD_UNSUPPORTED: Unsupported card type (0x5B0) in slot 1/1.
*May 20 09:12:13: %IPCOIR-3-CARD_UNSUPPORTED: Unsupported card type (0x5B0) in slot 2/1.
*May 20 09:12:16: %IPCOIR-5-CARD_DETECTED: Card type unknown (0x641) in slot 5/1
*May 20 09:12:16: %IPCOIR-3-CARD_UNSUPPORTED: Unsupported card type (0x641) in slot 5/1.
*May 20 09:12:16: %IPCOIR-3-CARD_UNSUPPORTED: Unsupported card type (0x641) in slot 5/1.

Config file :
boot-start-marker
boot system disk0:ubr10k2-k9p6u2-mz.123-17b.BC9.bin
boot-end-marker
!
enable secret 5 $1$cmvj$lKu9Yq8bAginvUuTH9l/f1
enable password 7 0835494319485744
!
clock timezone EST -5
clock summer-time EST recurring
facility-alarm intake-temperature major 49
facility-alarm intake-temperature minor 40
facility-alarm core-temperature major 53
facility-alarm core-temperature minor 45
card 1/1 Unknown (type 0)
card 4/0 1gigethernet-hh-1
card 5/1 Unknown (type 0)
no cable qos permission create
no cable qos permission update
cable qos permission modems
no aaa new-model
ip subnet-zero
!
!
redundancy

!
!
!
!
interface FastEthernet0/0/0
ip address 192.168.3.2 255.255.255.252
duplex full
speed 100
!
interface GigabitEthernet4/0/0
no negotiation auto
!
ip classless
ip route 0.0.0.0 0.0.0.0 192.168.3.2
no ip http server
no ip http secure-server
!
!
!
cdp run
!
!
line con 0
line aux 0
line vty 0 4
login local
!
ntp clock-period 17180517
ntp server 192.168.3.1
end

Killa200
Mc20x20

The Mc20x20 card doesn't require any timing cards to be present in the chassis in order to operate correctly. Unless you have the costly time generation equipment that needs to be installed along with the DTCC cards I would skip setting them up.

wrangler
Hi,

Hi,

I tried what you told, and i dont look as he see the mc20x20 card. Doesnt appears in show inventory and normally. how can we see if working well ?

kwesibrunee
You need a much newer IOS

You need a much newer IOS

from the config guide: at http://www.cisco.com/c/en/us/td/docs/interfaces_modules/cable/broadband_...

Prerequisites for Configuring the Cisco UBR-MC20X20V Cable Interface Line Card

The Cisco UBR-MC20X20V cable interface line card is supported on the Cisco CMTS routers and follows these general prerequisites when being implemented on the Cisco CMTS.

•The Cisco UBR10012 universal broadband router must be running Cisco IOS 12.2(33)SCC release or later to support the Cisco UBR-MC20X20V cable interface line card.

•The Cisco uBR10012 universal broadband router must have two DOCSIS Timing, Communication and Control (DTCC) cards configured before installing the Cisco UBR-MC20X20V cable interface line card.

Believe it or not 12.3.17 is much much much older than 12.2.33 SCC, Cisco stopped developing the 12.3 series of IOS years ago and all current and future development is on the 12.2 series of IOS. That is the one you want to run.

The release date on 12.3.17b is 08-OCT-2007 the release date on 12.2.33 SCC7 is 06-APR-2011, the latest IOS is 12.2.33SCI1 with a release of 18-FEB-2015.

wrangler
hi,

hi,

thank you for the info is very useful, anyone have this release of IOS 12.2.33SCI1 ?

thanks

mbowe
Dont go for SCI1, you want

Dont go for SCI1, you want something with a higher last digit

Low numbers means it is new software and likely pretty buggy

SCG7 <-- works well on our MC20x20V
SCH5 <-- Current recommended release by Cisco, we havent got around to upgrading to it yet

wrangler
thank for this information.

thank for this information. Very useful. Could you provide me the version SCG7 on my email ? wrangler77@gmail.com

thanks for your help.

gerta (not verified)
Card UBR10-MC20X20H loading

Hi

I am having this issue with UBR10-MC20X20H card, it stays in loading state. It was working ok, but we have to reboot the cmts and after that the card cant come online and it is stuck on loading:

%IPCOIR-5-CARD_LOADING: Loading card in slot 8/1 sw version 1.0 code MD5 D41D8CD98F00B204E9800998ECF8427E fpga MD5 0000000000000000000000000
0000000

THe UBR10000 is running on this version 12.2(33)SCE5. Should I upgrade it or it can work with this.

Thank you for your attention,

Log in or register to post comments