Not sure what equipment you're running, but a 2x8 cannot do upstream bonding if that's what you're running. The cards are not capable of upstream bonding.
On an RX48 you CAN do upstream bonding between two physical ports, but I can't think of any reason why you would want to since each physical port can handle up to 6 upstreams logically on that card. [edit--Of course, you might have an 80mhz upstream range, so that would make sense, see further below edit for what should work]
What image version, equipment, and bootrom are you running?
[edit]
If you're EuroDOCSIS, I'm going to use examples of RX48 ports 0/0 and 0/1. I'm only done this accidentally without the intention of doing it, so don't take my word for it, but hopefully this gets you in the right direction.
0/1 you'll want to remove all of the configuration entirely, and bind your upstreams and downstreams to the 0/0 interface. For 8 upstream bonding.
It should give you an error if you have frequencies overlapping.
Hope this helps, and again I've only done this on accident and unintentionally, so I could be completely wrong.
Hello everyone,
I want to combine 2 ports downstream and 2 ports upstream, but i can't use the command :
cable upstream bonding-group 7737 0/0/0 0/1/0 0/2/0 0/3/0 1/0/0 1/1/0 1/2/0 1/3/0
anyone can tell me any solution?
Thanks so much!
config should look like this
cable upstream port 0/0
cable upstream physical-delay automatic
cable upstream 0 description Node 7
cable upstream 0 frequency 37800000
cable upstream 0/0 channel-type atdma
cable upstream 0/0 pre-equalization
cable upstream 1 description Node 7
cable upstream 1 frequency 31000000
cable upstream 1/0 channel-type mtdma
cable upstream 1/0 pre-equalization
no cable upstream 0/0 shutdown
no cable upstream 0 shutdown
no cable upstream 1/0 shutdown
no cable upstream 1 shutdown
cable upstream 2/0 shutdown
cable upstream 2 shutdown
cable upstream 3/0 shutdown
cable upstream 3 shutdown
cable upstream 4/0 shutdown
cable upstream 4 shutdown
cable upstream 5/0 shutdown
cable upstream 5 shutdown
cable upstream fiber-node FN-0
no cable upstream shutdown
!
cable upstream port 0/1
cable upstream physical-delay automatic
cable upstream 0 description Node 8
cable upstream 0 frequency 37800000
cable upstream 0/0 channel-type atdma
cable upstream 0/0 pre-equalization
cable upstream 1 description Node 8
cable upstream 1 frequency 31000000
cable upstream 1/0 channel-type mtdma
cable upstream 1/0 pre-equalization
no cable upstream 0/0 shutdown
no cable upstream 0 shutdown
no cable upstream 1/0 shutdown
no cable upstream 1 shutdown
cable upstream 2/0 shutdown
cable upstream 2 shutdown
cable upstream 3/0 shutdown
cable upstream 3 shutdown
cable upstream 4/0 shutdown
cable upstream 4 shutdown
cable upstream 5/0 shutdown
cable upstream 5 shutdown
cable upstream fiber-node FN-1
no cable upstream shutdown
!
interface cable 0/0
description Nodes 7 8
cable bundle 1
no ip address
mdrc enable
ip access-group 191 in
cable bind downstream 13/2/0,13/2/1,13/2/2,13/2/3,13/3/0,13/3/1,13/3/2,13/3/3
cable bind upstream 0/0,0/1,1/0,1/1
cable dynamic-service authorization-mode unauthorize
cable dynamic-service active-timeout 60
no shutdown
cable downstream bonding-group 1 13/2/0 13/2/1 13/2/2 13/2/3
cable downstream bonding-group 3 13/2/0 13/2/1 13/2/2 13/2/3 13/3/0 13/3/1 13/3/2 13/3/3
cable downstream bonding-group 2 13/3/0 13/3/1 13/3/2 13/3/3
cable upstream bonding-group 20 0/0/0 0/1/0
cable upstream bonding-group 21 1/0/0 1/1/0
cable mtc-mode
cable t4-multiplier 4
ip dhcp relay information option
host authorization on
dhcp leasequery authorization on
cable flap-list insertion-time 1
cable flap-list power-adjust threshold 10
cable flap-list size 8191
cable flap-list miss-threshold 12
!
config should look like this
cable upstream port 0/0
cable upstream physical-delay automatic
cable upstream 0 description Node 7
cable upstream 0 frequency 37800000
cable upstream 0/0 channel-type atdma
cable upstream 0/0 pre-equalization
cable upstream 1 description Node 7
cable upstream 1 frequency 31000000
cable upstream 1/0 channel-type mtdma
cable upstream 1/0 pre-equalization
no cable upstream 0/0 shutdown
no cable upstream 0 shutdown
no cable upstream 1/0 shutdown
no cable upstream 1 shutdown
cable upstream 2/0 shutdown
cable upstream 2 shutdown
cable upstream 3/0 shutdown
cable upstream 3 shutdown
cable upstream 4/0 shutdown
cable upstream 4 shutdown
cable upstream 5/0 shutdown
cable upstream 5 shutdown
cable upstream fiber-node FN-0
no cable upstream shutdown
!
cable upstream port 0/1
cable upstream physical-delay automatic
cable upstream 0 description Node 8
cable upstream 0 frequency 37800000
cable upstream 0/0 channel-type atdma
cable upstream 0/0 pre-equalization
cable upstream 1 description Node 8
cable upstream 1 frequency 31000000
cable upstream 1/0 channel-type mtdma
cable upstream 1/0 pre-equalization
no cable upstream 0/0 shutdown
no cable upstream 0 shutdown
no cable upstream 1/0 shutdown
no cable upstream 1 shutdown
cable upstream 2/0 shutdown
cable upstream 2 shutdown
cable upstream 3/0 shutdown
cable upstream 3 shutdown
cable upstream 4/0 shutdown
cable upstream 4 shutdown
cable upstream 5/0 shutdown
cable upstream 5 shutdown
cable upstream fiber-node FN-1
no cable upstream shutdown
!
interface cable 0/0
description Nodes 7 8
cable bundle 1
no ip address
mdrc enable
ip access-group 191 in
cable bind downstream 13/2/0,13/2/1,13/2/2,13/2/3,13/3/0,13/3/1,13/3/2,13/3/3
cable bind upstream 0/0,0/1,1/0,1/1
cable dynamic-service authorization-mode unauthorize
cable dynamic-service active-timeout 60
no shutdown
cable downstream bonding-group 1 13/2/0 13/2/1 13/2/2 13/2/3
cable downstream bonding-group 3 13/2/0 13/2/1 13/2/2 13/2/3 13/3/0 13/3/1 13/3/2 13/3/3
cable downstream bonding-group 2 13/3/0 13/3/1 13/3/2 13/3/3
cable upstream bonding-group 20 0/0/0 0/1/0
cable upstream bonding-group 21 1/0/0 1/1/0
cable mtc-mode
cable t4-multiplier 4
ip dhcp relay information option
host authorization on
dhcp leasequery authorization on
cable flap-list insertion-time 1
cable flap-list power-adjust threshold 10
cable flap-list size 8191
cable flap-list miss-threshold 12
!
Not sure what equipment you're running, but a 2x8 cannot do upstream bonding if that's what you're running. The cards are not capable of upstream bonding.
On an RX48 you CAN do upstream bonding between two physical ports, but I can't think of any reason why you would want to since each physical port can handle up to 6 upstreams logically on that card. [edit--Of course, you might have an 80mhz upstream range, so that would make sense, see further below edit for what should work]
Here's upstream bonding on an RX48.
cable bind downstream 1/6/0,1/6/1,1/6/2,1/6/3,1/7/0,1/7/1,1/7/2,1/7/3
cable bind upstream 7/0,7/1,7/2,7/3
cable dynamic-service authorization-mode unauthorize
cable dynamic-service active-timeout 60
no shutdown
cable downstream bonding-group 3710 1/6/0 1/6/1 1/6/2 1/6/3 1/7/0 1/7/1 1/7/2 1/7/3
cable downstream bonding-group 3711 1/6/0 1/6/1 1/6/2 1/6/3
cable downstream bonding-group 3712 1/7/0 1/7/1 1/7/2 1/7/3
cable upstream bonding-group 7357 7/0/0 7/1/0 7/2/0 7/3/0
What image version, equipment, and bootrom are you running?
[edit]
If you're EuroDOCSIS, I'm going to use examples of RX48 ports 0/0 and 0/1. I'm only done this accidentally without the intention of doing it, so don't take my word for it, but hopefully this gets you in the right direction.
0/1 you'll want to remove all of the configuration entirely, and bind your upstreams and downstreams to the 0/0 interface. For 8 upstream bonding.
cable bind upstream 0/0,0/1,0/2,0/3,1/0,1/1,1/2,1/3
cable upstream bonding-group 0/0/0 0/1/0 0/2/0 0/3/0 1/0/0 1/1/0 1/2/0 1/3/0
It should give you an error if you have frequencies overlapping.
Hope this helps, and again I've only done this on accident and unintentionally, so I could be completely wrong.
Hello everyone,
I want to combine 2 ports downstream and 2 ports upstream, but i can't use the command :
cable upstream bonding-group 7737 0/0/0 0/1/0 0/2/0 0/3/0 1/0/0 1/1/0 1/2/0 1/3/0
anyone can tell me any solution?
Thanks so much!