Hello , does someone know who to use theus feature of the BSR64K ?, is there the need of using a software besides the configuration of the fft and snr made on the BSR? , I have noticed that when a display , for instance
BSR#fft display 2/1 startfreq 0 endfreq 81920000 table
Power Level Measurement - Slot : 2, Port : 1
==================================================
Number of Samples : 512, 9th Receiver Opmode : Tap-in
Window Coefficient used : Rectangular
Start Frequency : 0 Hz, End Frequency : 81920000 Hz
Frequency Step Size : 320000 Hz
Frequency (Hz) Power Level (dB)
-------------- ----------------
0 -39.9222
320000 -67.476
640000 -71.3327
960000 -78.0045
1280000 -84.2884
1600000 -90.309
1920000 -87.2987
2240000 -83.3193
2560000 -78.0045
2880000 -83.3193
3200000 -74.2884
3520000 -78.8477
3840000 -61.6698
4160000 -71.5009
..............................................
thouse level are the level of the signal reaching the CMTS on the upstream port ?, why are they negative ?
And , when I display for instance
BSR#snr display 2 7
SNR Setup: slot 2 upstream 7 Start Freq 5000000 End Freq 42000000 channel-width 6400000
modulation-type Auto ingress-cancel Auto equalization On
SNR Reference modem: 001a.6637.47ca
SNR Timestamp: MON NOV 24 16:55:46 2008
Center Freq Mode Equalization Ingress SNR
----------------- ------- ------------ -------- -------
8200000 QPSK On On 35.3
8200000 QPSK On Off 34.6
8200000 16QAM On On 33.0
8200000 16QAM On Off 32.7
14600000 QPSK On On 36.5
14600000 QPSK On Off 35.8
14600000 16QAM On On 35.8
14600000 16QAM On Off 35.3
21000000 QPSK On On 36.1
21000000 QPSK On Off 36.1
21000000 16QAM On On 34.6
21000000 16QAM On Off 34.4
27400000 QPSK On On 35.8
27400000 QPSK On Off 35.6
27400000 16QAM On On 33.8
27400000 16QAM On Off 33.3
why is there only thouse tyes of modulation if in a CMTS 2x8 Module I work with docsis2.0 and 64QAM, this can not give a real measure , there is no option to choose 64QAM.
I appreciate any response . Regards.
Please post the output from show chassis stat and we can go from there
Carl
hello , this the sh chassis status
ROUTER#sh chassis status
Slot Type Sub Red State RM IO UpTime LastUpTime Success Failure
0 CMTS 2x8(2.0) 6 RUN x x 21w5d14h 1 0
1 CMTS 2x8(2.0) 6 RUN x x 21w5d14h 1 0
2 CMTS 2x8(2.0) 6 RUN x x 21w5d14h 1 0
3 CMTS 2x8(2.0) 6 RUN x x 21w5d14h 1 0
4 CMTS 2x8(2.0) 6 RUN x x 21w5d14h 1 0
5 CMTS 2x8(2.0) 6 RUN x x 21w5d14h 1 0
6 CMTS 2x8(2.0) - stby x x 21w5d14h 1 0
7 SRM4 - stby x x 2w1d7h 19w4d7h 2 1
8 SRM4 7 RUN x - 21w5d14h 0 0
9 CMTS 2x8(2.0) 6 RUN x x 21w5d14h 1 0
10 CMTS 2x8(2.0) 6 RUN x x 21w5d14h 1 0
11 CMTS 2x8(2.0) 6 RUN x x 21w5d14h 1 0
12 CMTS 2x8(2.0) 6 RUN x x 21w5d14h 1 0
13 CMTS 2x8(2.0) 6 RUN x x 21w5d14h 2 0
14 HSIM SMGE - RUN x x 21w5d14h 1 0
15 HSIM SMGE - RUN x x 21w5d14h 1 0
I appreciate your help
I wanted to see the type of cards, but you left of the software the system is running. could you report the output with the image as well?
Thanks
Carl