I had a working test on the MC20x20V. Today when I arrived the test modem had no Upstream. This is the output I get now.
Router#sh controllers cable 6/1/0
Interface Cable6/1/0
Hardware is MC2020V
Upstream MAC Processor Powered by Jib3 Upstream FPGA Complex
Jib3 Upstream FPGA is NOT Initialized
Jib3US Initializtion Error Code: 9
Jib3US Initializtion Status : SPI4E Snk Core Didn't Acquire Sync Frame
Jib3 Upstream FPGA Information
Flora FPGA Rev ID = 0x00000006
Flora FPGA HW Rev ID = 0x00000006
Fauna FPGA Rev ID = 0x00000006
Fauna FPGA HW Rev ID = 0x00000014
Jib3US Hardware Flow State Info - Segment 0
Bonded HwFlows Free = 16384
Bonded HwFlows Used = 0
Bonded HwFlows Wait = 0
NonBonded HwFlows Free = 114688
NonBonded HwFlows Used = 0
NonBonded HwFlows Wait = 0
-------------------------------
Total Jib3US HwFlows = 131072
Jib3US State = Active, Active Seg = 0, Clr Rldram Done = False, CCF Done=False
alloc_head_tail_errors = 0
dealloc_head_tail_errors = 0
alloc_ses_state_errors = 0
dealloc_ses_state_errors = 0
waitList_errors = 0
port_validation_errors = 0
HCCP HA FLAGS:
linestate: TRUE hccpstate: FALSE hccpready: FALSE hccp_if_inited: FALSE
hccphopready: TRUE hccp_keepalive: FALSE hccp_critical: FALSE
ha_critical: FALSE drop_mac_msgs: FALSE rp_cms_recovering: FALSE
current_active_segment: 0
Cable6/1/0 JIB hardware status:
JIB Upstream port 0 Disabled Bound to local = 0
JIB Upstream port 1 Disabled Bound to local = 0
JIB Upstream port 2 Disabled Bound to local = 0
JIB Upstream port 3 Disabled Bound to local = 0
idb 0x1DCF39D8
Corabi IOFPGA Information:
Rev ID: 0x00000053 Watchodg Timer: Enabled Flowbit Generation: Enabled
Interrupt Counts:
Total Schooner Backplane Events: 1
Total TimeStamp (TSS) Interrupts: 2
TimeStamp Mismatch: 1
TimeStamp Reload: 1
Timestamp is from TCC card
WDOG L1 Timeout False Detection : Enabled, Last Reset Reason: 0x0
WDOG False - Total Count: 0, Last DEC val: 0x0
throttled 0 enabled 0 disabled 0
Rx: spurious 0 framing_err 0 hcs_err 0 no_buffer 0 short_pkt 0
no_enqueue 0 no_enp 0 miss_count 0 latency 0
invalid_sid 0 invalid_mac 0 bad_ext_hdr_pdu 0 concat 0 bad-concat 0
Tx: full 0 drop 0 stuck 0 latency 0
MTx: full 0 drop 0 stuck 0 latency 0
Slots 0 NoUWCollNoEngy 0 FECorHCS 0 HCS 0
Req 0 ReqColl 0 ReqNoise 0 ReqNoEnergy 0
ReqData 0 ReqDataColl 0 ReqDataNoise 0 ReqDataNoEnergy 0
Rng 0 RngColl 0 RngNoise 0
FECBlks 0 UnCorFECBlks 0 CorFECBlks 0
MAP FIFO overflow 0, Rx FIFO overflow 0, No rx buf 0
DS FIFO overflow 0, US FIFO overflow 0, US stuck 0
Bandwidth Requests= 0x0
Piggyback Requests= 0x0
Ranging Requests= 0x0
Timing Offset = 0x0
Bad bandwidth Requests= 0x0
Bad REG_ACK= 0x0
No MAP buffer= 0x0 No Remote MAP buffer= 0x0
No REG_RESP buffer= 0x0
Cable6/1/0 Downstream is up
Frequency not set, Channel Width 6 MHz, 64-QAM, Symbol Rate 5.056941 Msps
FEC ITU-T J.83 Annex B, R/S Interleave I=32, J=4
Downstream channel ID: 73
Dynamic Services Stats:
DSA: 0 REQs 0 RSPs 0 ACKs
0 Successful DSAs 0 DSA Failures
DSC: 0 REQs 0 RSPs 0 ACKs
0 Successful DSCs 0 DSC Failures
DSD: 0 REQs 0 RSPs
0 Successful DSDs 0 DSD Failures
DBC: 0 REQs 0 RSPs(Rcvd) 0 ACKs
0 Successful DBCs 0 DBC Failures 0 DBC Partial
0 DBC Protocol Violations
DCC: 0 REQs 0 RSPs 0 ACKs
0 Successful DCCs 0 DCC Failures
0 DCC Departs 0 DCC Arrives
DCC end of transaction counts:
DCC unknown cause(0) offline(0) if down(0) no cm(0)
DCC no resource(0) no retries(0) reject(0) unknown state (0)
DCC rebuild err (0) T15 timeout(0) wrong channel(0) reinit MAC (0)
DCC dcc succeeds(0)
DCC wcm(0)
CM STATUS Stats:
0 invalid_event 0 tlv_error
0 disabled_event 0 invalid_state
0 invalid_chid 0 prim_chid
Local total modems 0, modems active 0, total DS flows 1
MDDs Primary Non-Primary
----------------------------------------------
----------------------------------------------
Cable6/1/0 Upstream 0 is administratively down
Frequency not set, Channel Width 1.600 MHz, Symbol Rate 1.280 Msps
Modulations - Short QPSK, Long QPSK
This upstream is mapped to physical port 0
Spectrum Group is unassigned
MER(SNR) - Unknown - no modems online.
Nominal Input Power Level 0 dBmV, Tx Timing Offset 0
Ranging Backoff Start 3, Ranging Backoff End 6
US timing offset adjustment type 2, value 0
Ranging Insertion Interval automatic (60 ms)
US throttling off
Tx Backoff Start 3, Tx Backoff End 5
Modulation Profile Group 21
Concatenation is enabled
Fragmentation is enabled
part_id=0x0000, rev_id=0x00, rev2_id=0x00
nb_agc_thr=0x0000, nb_agc_nom=0x0000
Range Load Reg Size=0x58
Request Load Reg Size=0x0E
Minislot Size in number of Timebase Ticks is = 4
Minislot Size in Symbols = 32
Bandwidth Requests = 0x0
Piggyback Requests = 0x0
Invalid BW Requests= 0x0
Minislots Requested= 0x0
Minislots Granted = 0x0
Minislot Size in Bytes = 8
Map Advance (Dynamic) : 1600 usecs
Map Count = 0
Remote Map Counts: (none)
UCD Count = 0
Remote UCD Counts: (none)
PHY: us errors 0 us recoveries 2
MAC PHY TSS: tss error start 0 tss error end 0
MAC PHY Status: bcm3140 status 0 lookout status 0
Not Bound to Local Downstream
MAP/UCD Replication Instructions:
Cable6/1/0 Upstream 1 is administratively down
Frequency not set, Channel Width 1.600 MHz, Symbol Rate 1.280 Msps
Modulations - Short QPSK, Long QPSK
This upstream is mapped to physical port 1
Spectrum Group is unassigned
MER(SNR) - Unknown - no modems online.
Nominal Input Power Level 0 dBmV, Tx Timing Offset 0
Ranging Backoff Start 3, Ranging Backoff End 6
US timing offset adjustment type 2, value 0
Ranging Insertion Interval automatic (60 ms)
US throttling off
Tx Backoff Start 3, Tx Backoff End 5
Modulation Profile Group 21
Concatenation is enabled
Fragmentation is enabled
part_id=0x0000, rev_id=0x00, rev2_id=0x00
nb_agc_thr=0x0000, nb_agc_nom=0x0000
Range Load Reg Size=0x58
Request Load Reg Size=0x0E
Minislot Size in number of Timebase Ticks is = 4
Minislot Size in Symbols = 32
Bandwidth Requests = 0x0
Piggyback Requests = 0x0
Invalid BW Requests= 0x0
Minislots Requested= 0x0
Minislots Granted = 0x0
Minislot Size in Bytes = 8
Map Advance (Dynamic) : 1600 usecs
Map Count = 0
Remote Map Counts: (none)
UCD Count = 0
Remote UCD Counts: (none)
PHY: us errors 0 us recoveries 2
MAC PHY TSS: tss error start 0 tss error end 0
MAC PHY Status: bcm3140 status 0 lookout status 0
Not Bound to Local Downstream
MAP/UCD Replication Instructions:
Cable6/1/0 Upstream 2 is administratively down
Frequency not set, Channel Width 1.600 MHz, Symbol Rate 1.280 Msps
Modulations - Short QPSK, Long QPSK
This upstream is mapped to physical port 2
Spectrum Group is unassigned
MER(SNR) - Unknown - no modems online.
Nominal Input Power Level 0 dBmV, Tx Timing Offset 0
Ranging Backoff Start 3, Ranging Backoff End 6
US timing offset adjustment type 2, value 0
Ranging Insertion Interval automatic (60 ms)
US throttling off
Tx Backoff Start 3, Tx Backoff End 5
Modulation Profile Group 21
Concatenation is enabled
Fragmentation is enabled
part_id=0x0000, rev_id=0x00, rev2_id=0x00
nb_agc_thr=0x0000, nb_agc_nom=0x0000
Range Load Reg Size=0x58
Request Load Reg Size=0x0E
Minislot Size in number of Timebase Ticks is = 4
Minislot Size in Symbols = 32
Bandwidth Requests = 0x0
Piggyback Requests = 0x0
Invalid BW Requests= 0x0
Minislots Requested= 0x0
Minislots Granted = 0x0
Minislot Size in Bytes = 8
Map Advance (Dynamic) : 1600 usecs
Map Count = 0
Remote Map Counts: (none)
UCD Count = 0
Remote UCD Counts: (none)
PHY: us errors 0 us recoveries 2
MAC PHY TSS: tss error start 0 tss error end 0
MAC PHY Status: bcm3140 status 0 lookout status 0
Not Bound to Local Downstream
MAP/UCD Replication Instructions:
Cable6/1/0 Upstream 3 is administratively down
Frequency not set, Channel Width 1.600 MHz, Symbol Rate 1.280 Msps
Modulations - Short QPSK, Long QPSK
This upstream is mapped to physical port 3
Spectrum Group is unassigned
MER(SNR) - Unknown - no modems online.
Nominal Input Power Level 0 dBmV, Tx Timing Offset 0
Ranging Backoff Start 3, Ranging Backoff End 6
US timing offset adjustment type 2, value 0
Ranging Insertion Interval automatic (60 ms)
US throttling off
Tx Backoff Start 3, Tx Backoff End 5
Modulation Profile Group 21
Concatenation is enabled
Fragmentation is enabled
part_id=0x0000, rev_id=0x00, rev2_id=0x00
nb_agc_thr=0x0000, nb_agc_nom=0x0000
Range Load Reg Size=0x58
Request Load Reg Size=0x0E
Minislot Size in number of Timebase Ticks is = 4
Minislot Size in Symbols = 32
Bandwidth Requests = 0x0
Piggyback Requests = 0x0
Invalid BW Requests= 0x0
Minislots Requested= 0x0
Minislots Granted = 0x0
Minislot Size in Bytes = 8
Map Advance (Dynamic) : 1600 usecs
Map Count = 0
Remote Map Counts: (none)
UCD Count = 0
Remote UCD Counts: (none)
PHY: us errors 0 us recoveries 2
MAC PHY TSS: tss error start 0 tss error end 0
MAC PHY Status: bcm3140 status 0 lookout status 0
Not Bound to Local Downstream
MAP/UCD Replication Instructions:
Multicast/Broadcast RateLimit Dropped Pkts : 0
Crane VIF info:
Physical port 0 uses logical upstream 1 for idb = 0x1DCF39D8
Physical port 1 uses logical upstream 2 for idb = 0x1DCF39D8
Physical port 2 uses logical upstream 3 for idb = 0x1DCF39D8
Physical port 3 uses logical upstream 4 for idb = 0x1DCF39D8
Crane BPI info: Segment Peer
Active 0 0/0
Crane BPI index table: indexes = 0, Next index = 101
The indexes on the free queue:
1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20
21 22 23 24 25 26 27 28 29 30 31 32 33 34 35 36 37 38 39 40
41 42 43 44 45 46 47 48 49 50 51 52 53 54 55 56 57 58 59 60
61 62 63 64 65 66 67 68 69 70 71 72 73 74 75 76 77 78 79 80
81 82 83 84 85 86 87 88 89 90 91 92 93 94 95 96 97 98 99 100
Total indexes on free queue 100
Encapstr sid mismatches : 0
Cable6/1/0 Upstream 0 is administratively down,
sounds like the interface is shutdown....
did you "no" out the shutdown line i.e.
interface cable 6/1/0
no cable upstream 0 shutdown
perhaps you forgot to save the config and the router lost power and reverted to old config.
I have.... This was after a clear of the config. As soon as the card boots It give me the Jib3US not Initialized...