You are here

Wideband balancing

2 posts / 0 new
Last post
mipq
Wideband balancing

Hi

I have UBR10K 12.2(33)SCH2, there is three widebands:

Wideband-5/0/0:0 16x4(frequency 362-418MHz 770-826MHz)
Wideband 5/0/0:1 8x4(freq 362-418MHz)
Wideband 5/0/0:2 8x4(770-826MHz)

Problem with modems 8x4 modems loging only to first wideband 8x4 5/0/0:1. I want investigate in order to modems bonding to second wideband 8x4 5/0/0:2, something like load balancing.

Below my config:

interface Wideband-Cable5/0/0:0
cable bundle 1
cable rf-channel 0 bandwidth-percent 1 remaining ratio 100
cable rf-channel 1 bandwidth-percent 1 remaining ratio 100
cable rf-channel 2 bandwidth-percent 1 remaining ratio 100
cable rf-channel 3 bandwidth-percent 1 remaining ratio 100
cable rf-channel controller 1 channel 0 bandwidth-percent 1 remaining ratio 100
cable rf-channel controller 1 channel 1 bandwidth-percent 1 remaining ratio 100
cable rf-channel controller 1 channel 2 bandwidth-percent 1 remaining ratio 100
cable rf-channel controller 1 channel 3 bandwidth-percent 1 remaining ratio 100
cable rf-channel controller 2 channel 0 bandwidth-percent 1 remaining ratio 100
cable rf-channel controller 2 channel 1 bandwidth-percent 1 remaining ratio 100
cable rf-channel controller 2 channel 2 bandwidth-percent 1 remaining ratio 100
cable rf-channel controller 2 channel 3 bandwidth-percent 1 remaining ratio 100
cable rf-channel controller 3 channel 0 bandwidth-percent 1 remaining ratio 100
cable rf-channel controller 3 channel 1 bandwidth-percent 1 remaining ratio 100
cable rf-channel controller 3 channel 2 bandwidth-percent 1 remaining ratio 100
cable rf-channel controller 3 channel 3 bandwidth-percent 1 remaining ratio 100
!
interface Wideband-Cable5/0/0:1
cable bundle 1
cable rf-channel 0 bandwidth-percent 1 remaining ratio 100
cable rf-channel 1 bandwidth-percent 1 remaining ratio 100
cable rf-channel 2 bandwidth-percent 1 remaining ratio 100
cable rf-channel 3 bandwidth-percent 1 remaining ratio 100
cable rf-channel controller 1 channel 0 bandwidth-percent 1 remaining ratio 100
cable rf-channel controller 1 channel 1 bandwidth-percent 1 remaining ratio 100
cable rf-channel controller 1 channel 2 bandwidth-percent 1 remaining ratio 100
cable rf-channel controller 1 channel 3 bandwidth-percent 1 remaining ratio 100
!
interface Wideband-Cable5/0/0:2
cable bundle 1
cable rf-channel controller 2 channel 0 bandwidth-percent 1 remaining ratio 100
cable rf-channel controller 2 channel 1 bandwidth-percent 1 remaining ratio 100
cable rf-channel controller 2 channel 2 bandwidth-percent 1 remaining ratio 100
cable rf-channel controller 2 channel 3 bandwidth-percent 1 remaining ratio 100
cable rf-channel controller 3 channel 0 bandwidth-percent 1 remaining ratio 100
cable rf-channel controller 3 channel 1 bandwidth-percent 1 remaining ratio 100
cable rf-channel controller 3 channel 2 bandwidth-percent 1 remaining ratio 100
cable rf-channel controller 3 channel 3 bandwidth-percent 1 remaining ratio 100
!

Does anybody can reply me how to do.

mbowe
1/ Which of these downstream

1/ Which of these downstream channels are primary enabled?

2/ Do you have any load-balance configured eg
cable load-balance docsis-enable
cable load-balance docsis30-enable downstream-only

docsis